In vitro evaluation of novel titania-containing borate bioactive glass scaffolds.

Titanium-containing borate bioactive glass scaffolds (0, 5, 15, and 20 mol %, identified as BRT0, BRT1, BRT3, and BRT4) with a microstructure similar to that of human trabecular bone were prepared and evaluated in vitro for potential bone loss applications in revision total knee arthroplasty (rTKA). Methyl thiazolyl tetrazolium (MTT) cell viability assays of scaffold ion release extracts revealed that BRT0 scaffolds (0 mol % titanium) inhibited cell proliferation and activity at day 14. At day 30, all scaffold extracts decreased cell proliferation and activity significantly. However, live/dead cell assay results demonstrated that degradation products from all the scaffolds had no inhibitory effect on cell viability. Significant bactericidal efficacies of BRT3 extracts against Escherishia coli (Gram-negative) and BRT1 extracts against Staphylococcus aureus and Staphylococcus epidermidis (both Gram-positive bacteria) were demonstrated. Finally, evaluation of the cell/bioactive glass surface interactions showed well-spread cells on the surface of the BRT3 glass discs and BRT1 and BRT3 scaffolds, when compared to BRT0 and BRT4 scaffolds. The results indicate that by changing the Ti4+ :B3+ ratio, the ion release and consequently cell proliferation could be improved. in vitro results in this study demonstrate that BRT3 scaffolds could be a promising candidate for addressing bone loss in rTKAs; however, in vivo studies would be required to evaluate the effect of a dynamic environment on the cell and tissue response to the fabricated scaffolds.

Effect of TiO2 doping on degradation rate, microstructure and strength of borate bioactive glass scaffolds.

A titanium-containing borate glass series based on the system (52-X) B2O3-12CaO-6P2O5-14Na2O-16ZnO-XTiO2 with X varying from 0, 5 and 15 mol% of TiO2 incorporated, identified as BRT0, BRT1 and BRT3, respectively, were used in this study. Scaffolds (pore sizes, 165-230 µm and porosity, 53.51-69.51%) were prepared using a polymer foam replication technique. BRT3 scaffolds exhibited higher compressive strength (7.16 ±â€¯0.22 MPa) when compared to BRT0 (6.02 ±â€¯0.47 MPa) and BRT1 (5.65 ±â€¯0.28 MPa) scaffolds with lower, or no, TiO2 content. The solubility of the scaffolds decreased as the TiO2 content increased up to 15 mol% when samples of each scaffold were immersed in DI water and the pH of all these extracts went up from 7.0 to 8.5 in 30 days. The cumulative ion release from the scaffolds showed significant difference with respect to TiO2 content; addition of 5 mol% TiO2 at the expense of borate (B2O3) decreased the ion release remarkably. Furthermore, it was found that for all three scaffolds, cumulative ion release increased with incubation time. The results indicate that the degradation rates and compressive strengths of borate bioactive glass scaffolds could be controlled by varying the amount of TiO2 incorporated, confirming their potential as scaffolds in TKA and rTKA.

A review of materials for managing bone loss in revision total knee arthroplasty.

In 2014-2015, 61,421 total knee arthroplasties (TKAs) were performed in Canada; an increase of about 20% over 2000-2001. Revision total knee arthroplasties (rTKAs) accounted for 6.8% of TKAs performed between 2014 and 2015, and this is estimated to grow another 12% by 2025. rTKAs are typically more complicated than primary TKAs due to the significant loss of femoral and tibial bone stock. The escalating demand and limitations associated with total knee arthroplasty and their revision drives the development of novel treatments. A variety of materials have been utilized to facilitate regeneration of healthy bone around the site of a knee arthroplasty. The selection of these materials is based on the bone defect size and includes bone grafts, graft substitutes and cements. However, all these materials have certain disadvantages such as blood loss, disease transmission (bone grafts), inflammatory response, insufficient mechanical properties (bone graft substitutes) thermal necrosis and stress shielding (bone cement). Recently, the use of metal augments for large bone defects has attracted attention, however they can undergo fretting, corrosion, and stress shielding. All things considered, this review indicates the necessity of developing augments that have structural integrities and biodegradation rates similar to that of human bone. Therefore, the future of bone loss management may lie in fabricating novel bioactive glass augments as they can promote bone healing and implant stability and can degrade with time.

Sporicidal efficacy of thermal-sprayed copper alloy coating.

Approximately 200 000 Canadians acquire healthcare-associated bacterial infections each year and several-fold more acquire food-borne bacterial illnesses. Bacterial spores are particularly problematic because they can survive on surfaces for several months. Owing to its sporicidal activity, copper alloy sheet metal is sometimes used in hospital settings, but its widespread use is limited by cost and incompatibility with complex furniture and instrument designs and topographies. A potential alternative is the use of thermal spray technology to coat surfaces with copper alloys. We compared the sporicidal activity of thermally sprayed copper alloy on stainless steel with that of copper alloy sheet metal against Bacillus subtilis spores. Spores remained intact for at least 1 week on uncoated stainless steel, whereas spore fragmentation was initiated within 2 h of exposure to either copper surface. Less than 15% of spores were viable 2 h after exposure to either copper surface, as compared with stainless steel. By day 7, only degraded spores and petal-like nanoflowers were present on the copper surfaces. Nanoflowers, which are laminar arrangements of thin crystal sheets composed of carbon - copper phosphate, appeared to be derived from the degraded spores. Altogether, these results indicate that a thermal-sprayed copper alloy coating on stainless steel provides sporicidal activity similar to that afforded by copper alloy sheet metal.